CAN/CSA B1800-02 Plastic Nonpressure Pipe Compendium - B1800 Series (Consists of B181.1, B181.2, B181.3, B181.5, B182.1, B182.2, B182.4, B182.6, B182.7, B182.8 and B182.11)

standard by Canadian Standards Association / National Standard of Canada, 08/01/2002

Full Description

1. Scope1.1This Standard applies to acrylonitrile-butadiene-styrene drain, waste, and vent (ABS-DWV) pipe, pipefittings, and accessories such as factory-assembled expansion joints, closet flanges, and backwater valves.1.2This Standard includes requirements for materials, quality of work, dimensions and tolerances, impactstrength, chemical resistance, water resistance, dimensional stability, hydrostatic strength, solventcement, and marking, as well as performance requirements for expansion joints, closet flanges, andbackwater valves.Notes:(1) Recommended installation practices for ABS-DWV pipe are given in Appendix A. Use of these recommendedpractices will help ensure proper installation and optimum service life.(2) The maximum pressure used to test DWV installations should be 100 kPa (14.5 psi) (see Clause A6.2).1.3The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.A1. ScopeA1.1 Data IncludedA1.1.1This Appendix applies to the installation of drain, waste, and vent systems for domestic, industrial, andcommercial plumbing.A1.1.2This Appendix includes instructions for handling and storage, system repair, installation, environmentalconditions, quality of work and assembly, and testing and inspection.A1.2 Data ExcludedRequirements for raw material, physical properties and dimensions of pipe and fittings, and solventcement are excluded from this Appendix. For such requirements, refer to the main Standard.B181.3-02Polyolefin Laboratory DrainageSystems1. Scope1.1This Standard provides requirements for polyolefin laboratory drainage systems for corrosiveapplications. Requirements for materials, pipe, and fittings are included.Note: Polyolefin includes both polyethylene and polypropylene plastics.1.2These requirements apply to pipe and fittings that are to be joined by heat fusion using the joiningequipment supplied by the manufacturer. This Standard is not intended to provide forinterchangeability between plastic pipe and fittings from different manufacturers, but it does allow fortransition fittings used to join one manufacturer?s product to another?s, provided that the joiningtechnique is other than heat fusion. For guidance on fusion joints and aboveground and undergroundinstallations, refer to Appendix A.1.3Systems having features differing from or additional to those covered by this Standard should beinvestigated to determine whether they comply with the intent of this Standard.B181.5-02Coextruded ABS/PVC Drain, Waste,and Vent Pipe1. Scope1.1This Standard applies to coextruded thermoplastic drain, waste, and vent (DWV) pipe with an outer layerof acrylonitrile butadiene styrene (ABS) and an inner layer of polyvinyl chloride (PVC) or with outer andinner layers of acrylonitrile butadiene styrene (ABS) and a core of polyvinyl chloride (PVC), to be usedwith fittings, accessories, and solvent cement meeting the requirements of CSA Standard B181.1.1.2This Standard includes requirements for materials, quality of work, dimensions and tolerances, impactstrength, chemical resistance, water resistance, dimensional stability, compression strength, extrusionquality, and bond strength.Note: Recommended storage, handling, and installation practices for coextruded ABS/PVC DWV pipe are provided inAppendix A. Use of these recommended practices will help to ensure proper installation and optimum service life.1.3The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.A1. ScopeA1.1 Data IncludedA1.1.1This Appendix applies to the installation of drain, waste, and vent systems for domestic, industrial, andcommercial plumbing.A1.1.2This Appendix includes instructions for handling and storage, system repair, installation, environmentalconditions, quality of work and assembly, and testing and inspection.A1.2 Data ExcludedRequirements for raw material, physical properties and dimensions of pipe and fittings, and solventcement are excluded from this Appendix. For such requirements, refer to the main Standard.B182.1-02Plastic Drain and Sewer Pipe andPipe Fittings1. Scope1.1This Standard provides requirements for the following:(a) plastic drain and sewer pipe and plastic pipe fittings with pipe stiffness of 275, 320, or 625 kPa,including both single-wall and coextruded dual-wall pipe with a smooth interior;(b) single-wall, noncorrugated, perforated plastic pipe and plastic pipe fittings;(c) coextruded dual-wall perforated plastic pipe with a smooth interior and corrugated exterior; and(d) solvent cement.Note: Industrial waste disposal lines should be installed only with the specific approval of the regulatory authoritybecause chemicals not commonly found in drains and sewers, and temperatures greater than 60?C, may be encountered.Guidance on the relationship between pipe stiffness and end use of pipe is given in Appendix A.1.2The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.B182.2-02PVC Sewer Pipe and Fittings (PSMType)1. ScopeThis Standard provides requirements and test methods for materials, dimensions, quality of work, pipestiffness, quality control, joining systems, and marking for SDR 28, 35, and 41 Type PSM PVC sewer pipeand fittings.Notes:(1) Industrial waste disposal lines should be installed only with specific approval of the regulatory authority, sincechemicals not commonly found in drains and sewers, and temperatures in excess of 60?C (140?F), may be encountered.(2) Nominal pipe size is indicated by an NPS designation, and actual dimensions are given in millimetres. For example,a pipe of NPS-10 size will be nominally 10 inches in diameter.1.2The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.B182.4-02Profile PVC Sewer Pipe and Fittings1. ScopeThis Standard provides requirements and test methods for materials, dimensions, quality of work, pipestiffness, quality control, joining systems, and a form of marking for polyvinyl chloride (PVC) profilesewer pipe and fittings of pipe stiffness PS70 and PS320, based on controlled inside diameter.Notes:(1) Pipe and fittings produced to meet the requirements of this Standard should be installed in accordance withCSA Standard B182.11.(2) Industrial waste disposal lines should be installed only with the specific approval of the regulatory authority, sincechemicals not commonly found in drains and sewers may be encountered, as well as temperatures in excess of 60?C.(3) For use of PS70 pipe, the appropriate regulatory authority should be consulted.B182.6-02Profile Polyethylene Sewer Pipe andFittings for Leak-Proof SewerApplications1. Scope1.1This Standard provides requirements and test methods for the materials, dimensions, quality of work,pipe stiffness, quality control, jointing systems, and marking for profile polyethylene (PE) pipe andfittings with a smooth interior for sanitary sewer and other gravity flow drainage applications requiringleak-proof performance. Profile wall pipe includes both open and closed profile with sizes based oncontrolled inside diameter.Notes:(1) Pipe and fittings produced to meet the requirements of this Standard should be installed in accordance withCSA Standard B182.11.(2) This Standard does not cover helical open profile pipe.(3) For use of 210 kPa pipe, the appropriate regulatory authority should be consulted.(4) Refer to Appendix A for recommended quality control test frequencies.(5) Refer to Appendix C for fitting patterns for uniform definitions of the lay length of fittings covered by this Standard.(6) It is recommended that purchase orders using this specification follow the recommended requirements in AppendixD to describe the desired products adequately.1.2The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.B182.7-02Multilayer PVC Sewer Pipe (PSMType) Having Reprocessed-RecycledContent1. ScopeNote: Pipe made to this Standard should not be used in the production of fabricated fittings, due to the lack of fielddata.1.1This Standard provides requirements and test methods for materials, dimensions, quality of work, pipestiffness, quality control, jointing systems, and marking for SDR 28, 35, and 41 multilayer PVC sewerpipe (PSM type).Notes:(1) Industrial waste disposal lines should be installed only with specific approval of the regulatory authority, sincechemicals not commonly found in drains and sewers, and temperatures in excess of 60?C (140?F), may be encountered.(2) Nominal pipe size is indicated by an NPS designation, and actual dimensions are given in millimetres. For example,a pipe of NPS-10 size will be nominally 10 inches in diameter.1.2Pipe made to this Standard is designed to be used with PVC fittings meeting the requirements ofCSA Standard B182.1 or B182.2.1.3The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.B182.8-02Profile Polyethylene Storm Sewerand Drainage Pipe and Fittings1. Scope1.1This Standard provides requirements and test methods for the materials, dimensions, quality of work,pipe stiffness, quality control, jointing systems, and marking for profile polyethylene (PE) storm sewerand drainage pipe and fittings with a smooth interior. Profile wall pipe includes both open and closedprofile, with sizes based on controlled inside diameter for gasketed leak-proof and nongasketedleak-proof applications.Notes:(1) Pipe and fittings produced to meet the requirements of this Standard should be installed in accordance withCSA Standard B182.11.(2) This Standard does not cover helical open profile pipe. The environmental stress crack resistance (ESCR)requirements in this Standard may not be suitable for helical open profile pipe.(3) Refer to Appendix A for recommended quality control test frequencies.(4) Refer to Appendix C for fitting patterns for uniform definitions of the lay length of fittings covered by this Standard.(5) It is recommended that purchase orders using this specification follow the recommendations in Appendix E todescribe the desired products adequately.1.2The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.B182.11-02Recommended Practice for theInstallation of Thermoplastic Drain,Storm, and Sewer Pipe and Fittings
1. Scope

1.1 This Standard provides requirements for installation and testing of thermoplastic pipe used for theconveyance of drain, storm, and sanitary effluent in gravity-flow systems.

Note: Users of this Standard should recognize that installation specifications cover a broad range of conditions for thermoplastic pipe. The engineer should tailor the installation specification to special conditions and the contract documents. The addendum or special conditions should specify any work or materials not covered by this Standard.

1.2 This Standard applies to pipe conforming to CSA Standards B182.1, B182.2, B182.4, B182.7, andB182.8.

1.3 The values given in SI (metric) units are the standard. The values given in parentheses are forinformation only.

Product Details

Published: 08/01/2002 Number of Pages: 321 File Size: 1 file , 2.7 MB