M00044252
New product
API Spec 17L1 (R2020) Specification for Flexible Pipe Ancillary Equipment, First Edition, Includes Errata 1 (2015), Errata 2 (2015)
standard by American Petroleum Institute, 03/01/2013
In stock
Warning: Last items in stock!
Availability date: 01/06/2022
API SPECIFICATION 17L1 FIRST EDITION, MARCH 2013
ERRATA 1, JANUARY 2015
ERRATA 2, NOVEMBER 2015
REAFFIRMED, AUGUST 2020
API publications necessarily address problems of a general nature. With respect to particular circumstances, local, state, and federal laws and regulations should be reviewed.
Neither API nor any of API's employees, subcontractors, consultants, committees, or other assignees make any warranty or representation, either express or implied, with respect to the accuracy, completeness, or usefulness of the information contained herein, or assume any liability or responsibility for any use, or the results of such use, of any information or process disclosed in this publication. Neither API nor any of API's employees, subcontractors, consultants, or other assignees represent that use of this publication would not infringe upon privately owned rights.
API publications may be used by anyone desiring to do so. Every effort has been made by the Institute to assure the accuracy and reliability of the data contained in them; however, the Institute makes no representation, warranty, or guarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss or damage resulting from its use or for the violation of any authorities having jurisdiction with which this publication may conflict.
API publications are published to facilitate the broad availability of proven, sound engineering and operating practices. These publications are not intended to obviate the need for applying sound engineering judgment regarding when and where these publications should be utilized. The formulation and publication of API publications is not intended in any way to inhibit anyone from using any other practices.
Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standard is solely responsible for complying with all the applicable requirements of that standard. API does not represent, warrant, or guarantee that such products do in fact conform to the applicable API standard.
Classified areas may vary depending on the location, conditions, equipment, and substances involved in any given situation. Users of this Specification should consult with the appropriate authorities having jurisdiction.
Users of this Specification should not rely exclusively on the information contained in this document. Sound business, scientific, engineering, and safety judgment should be used in employing the information contained herein.
All rights reserved. No part of this work may be reproduced, translated, stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission from the publisher. Contact the Publisher, API Publishing Services, 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001.
Copyright © 2013 American Petroleum Institute
Nothing contained in any API publication is to be construed as granting any right, by implication or otherwise, for the manufacture, sale, or use of any method, apparatus, or product covered by letters patent. Neither should anything contained in the publication be construed as insuring anyone against liability for infringement of letters patent.
Shall: As used in a standard, “shall” denotes a minimum requirement in order to conform to the specification.
Should: As used in a standard, “should” denotes a recommendation or that which is advised but not required in order to conform to the specification.
This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API standard. Questions concerning the interpretation of the content of this publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards, American Petroleum Institute, 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001. Requests for permission to reproduce or translate all or any part of the material published herein should also be addressed to the director.
Generally, API standards are reviewed and revised, reaffirmed, or withdrawn at least every five years. A one-time extension of up to two years may be added to this review cycle. Status of the publication can be ascertained from the API Standards Department, telephone (202) 682-8000. A catalog of API publications and materials is published annually by API, 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001.
Suggested revisions are invited and 200 Massachusetts Avenue, NW, Suite 1100, Washington, DC 20001, standards@api.org.
This standard shall become effective on the date printed on the cover but may be used voluntarily from the date of distribution. Standards referenced herein may be replaced by other international or national standards that can be shown to meet or exceed the requirements of the referenced standard.
This standard is under the jurisdiction of the API Subcommittee on Subsea Production Systems. API Subcommittee 17 documents consists of the following:
RP 17A, Design and Operation of Subsea Production Systems—General Requirements and Recommendations
RP 17B, Recommended Practice for Flexible Pipe
RP 17C, Recommended Practice on TFL (Through Flowline) Systems
Spec 17D, Design and Operation of Subsea Production Systems—Subsea Wellhead and Tree Equipment
Spec 17E, Specification for Subsea Umbilicals
Spec 17F, Specification for Subsea Production Control Systems
RP 17G, Recommended Practice for Completion/Workover Risers
RP 17H, Remotely Operated Vehicle (ROV) Interfaces on Subsea Production Systems
Spec 17J, Specification for Unbonded Flexible Pipe
Spec 17K, Specification for Bonded Flexible Pipe
Spec 17L1, Specification for Flexible Pipe Ancillary Equipment
RP 17L2, Recommended Practice for Flexible Pipe Ancillary Equipment
RP 17M, Recommended Practice on Remotely Operated Tool (ROT) Intervention Systems
RP 17N, Recommended Practice for Subsea Production System Reliabilityand Technical Risk Management
RP 17O, Recommended Practice for Subsea High Integrity Pressure Protection Systems (HIPPS)
RP 17P, Subsea Structures and Manifolds (in press)
RP 17Q, Subsea Equipment Qualification–Standardized Process for Documentation
iii
This specification is the result of a Joint Industry Project to develop a worldwide industry standard for the design, material selection, manufacture, documentation, testing, marking and packaging of flexible pipe ancillary equipment. The objective of this specification is to provide an integrated approach, together with API 17B, API 17J, API 17K and API 17L2, to the design of flexible pipe systems. Therefore it is intended that this document be used in close conjunction with these documents.
Within this document, “shall” is used to state that a provision is mandatory; “should” is used to state that a provision is not mandatory, but is recommended as good practice; “may” is used to state that a provision is optional.
Systeme Internationale (SI) units are identified first when cited in the document. United States Customary (USC) units may be given in brackets after the SI units.
Specification for Flexible Pipe Ancillary Equipment
This specification defines the technical requirements for safe, dimensionally and functionally interchangeable flexible pipe ancillary equipment that is designed and manufactured to uniform standards and criteria.
Minimum requirements are specified for the design, material selection, manufacture, testing, documentation, marking and packaging of flexible pipe ancillary equipment, with reference to existing codes and standards where applicable. See API 17L2 for guidelines on the use of ancillary equipment.
The applicability relating to a specific item of ancillary equipment is stated at the beginning of the particular section for the ancillary equipment in question.
This specification applies to the following flexible pipe ancillary equipment:
bend stiffeners;
bend restrictors;
bellmouths;
buoyancy modules and ballast modules;
subsea buoys;
tethers for subsea buoys and tether clamps;
riser and tether bases;
clamping devices;
piggy-back clamps;
repair clamps;
I/J-tube seals;
pull-in heads/installation aids;
connectors;
load-transfer devices;
mechanical protection;
fire protection.
This specification may be used for bonded flexible pipe ancillary equipment, though any requirements specific to these applications are not addressed.